STUDY OF MECHANICAL ANISOTROPY FORMATION IN ROLLED RING PRODUCTION
https://doi.org/10.17073/0021-3438-2016-1-32-38
Abstract
The effect of titanium alloy mechanical anisotropy on the performance of gas turbine engine (GTE) ring-shaped parts was analyzed with account for their production cycle. Necessary dependencies were provided for transverse strain identification when assessing anisotropy during forming. It was found that both transversal strain coefficients and metal strength increase during the forming process (forging and rolling). In addition, the rolling process facilitates the transversal isotropy occurrence in the ring material. The stress state in a hollow homogenous cylinder under internal and external pressures was examined to evaluate the effect of transverse strain coefficients on the structure functionality. This scheme describes operating conditions of GTE compressor disks spacer with a reasonable degree of certainty while ignoring axial loads. The analysis showed that the allowable internal pressure taken by the spacer increases with the increase of transverse strain coefficients.
About the Authors
V A. Kostyshev
Samara State Aerospace University
Russian Federation
Russian Federation
Dr. Sci. (Tech.), prof., Department of metal forming,
443086, Samara, Moskovskoe sh., 34
Ya. A. Erisov
Samara State Aerospace University
Russian Federation
Russian Federation
Cand. Sci. (Tech.), senior engineer, NIL-37,
443086, Samara, Moskovskoe sh., 34
References
1. Smirnov V.S., Durnev V.D. Teksturoobrazovanie metallov pri prokatke [Formation of texture in metals by rolling]. Moscow: Metallurgiya, 1971.
2. Grechnikov F.V. Deformirovanie anizotropnykh materialov: Rezervy intensifikatsii [Deformation of anisotropic materials: Intensification reserves]. Moscow: Mashinostroenie, 1998.
3. Grechnikov F.V., Uvarov V.V. Energeticheskoe uslovie plastichnosti pri raznykh po velichine predelakh tekuchesti na szhatie i rastyazhenie [Energy yield criteria at different tensile and compression yield stresses]. Izv. Samarskogo Nauchnogo Tsentra Ross. Akademii Nauk. 2008. No. 3. P. 881—883.
4. Grechnikov F.V., Erisov Ya.A. Razrabotka kriteriya plastichnosti dlya raschetov formoizmeneniya vysokoteksturirovannykh anisotropnykh zagotovok [Development of yield criteria for calculation of forming of highly textured anisotropic blanks]. Vestnik Samarskogo Gos. Aerokosm. Univ. 2012. No. 1. P. 94—99.
5. Kaibyshev O.A., Utyashev F.Z. Sverkhplastichnost’, izmelchenie struktury i obrabotka trudnodeformiruemykh splavov [Super plasticity, structure refinement and treatment of difficult-to-form alloys]. Moscow: Nauka, 2002.
6. Kaibyshev O.A., Utyashev F.Z. Superplasticity: microstructural refinement and superplastic roll forming. Futurepast: Inc. USA, ISTC Science & Technology Series. 2005. Vol. 3. P. 386.
7. Utyashev F.Z., Burlakov I.A., Geikin V.A., Morozov V.V., Mulyukov R.R., Nazarov A.A., Cukhorukov R.Yu. Nauchnуe osnovy visokoeffektivnoi tekhnologii raskatki osesimmetrichnykh detalei rotora gazoturbinnykh dvigatelei iz zharoprochnykh splavov [Scientific base of highly effective technology of ring rolling of axisymmetric parts of rotor of gas-turbine engine from super alloys]. Problemу mashinostroeniya i nadezhnosti mashin. 2013. No. 5. P. 96—105.
8. Bewlay B.P., Gigliotti M.F.X., Utyashev F.Z., Kaibyshev O.A. Superplastic roll forming of Ti alloys. Materials & Design. 2000. Vol. 21. No. 4. P. 287—295.
9. Bewlay B.P., Gigliotti M.F.X., Hardwicke C.U., Kaibyshev O.A., Utyashev F.Z., Salischev G.A. Net-shape manufacturing of aircraft engine disks by roll forming and hot die forging. J. Mater. Process. Technol. 2003. Vol. 135. No. 2—3. P. 324—329.
10. Ryoo J.S., Yang D.Y., Johnson W. The influence of process parameters on torque and load in ring rolling. J. Mech. Work. Technol. 1986. Vol. 12. No. 3. P. 307—321.
11. Allwood J.M., Tekkaya A.E., Stanistreet T.F. The development of ring rolling technology. Steel Res. Int. 2005. Vol. 76. No. 2—3. P. 111—120.
12. Johnson W., MacLeod I., Needham G. An experimental investigation into the process of ring or metal tyre rolling. Int. J. Mech. Sci. 1968. Vol. 10. No. 6. P. 455—468.
13. Murzov A.I. K voprosu o probleme deformatsii metalla, nakhodyashchegosya v zone valkov [Revisiting the problem of metal deformation in the rolls zone]. Aluminievie splavi i spetsial’nie materiali. 1977. No. 10. P. 134—143.
14. Kassandrova O.N., Lebedev V.V. Obrabotka rezul’tatov nablyudenii [Processing of results of observations]. Moscow: Nauka, 1970.
15. Zaidel A.N. Oshibki izmerenii fizicheskikh velichin [Errors of measuring quantities]. Leningrad: Nauka, 1974.
16. Engler O., Hirsch J. Control of recrystallisation texture and texture-related properties in industrial production of aluminium sheet. Int. J. Mater. Res. 2009. Vol. 100. No. 4. P. 564—575.
17. Uvarov V.V., Arishenskii Yu.M., Grechnikov F.V. O vozmozhnostyakh regulirovaniya anizotropii listovikh materialov [About the possibilities of controlling anisotropy of sheet materials]. Teoriya i tekhnologiya obrabotki metallov davleniem: Proceedings of KuAI. Kuibishev: KuAI, 1977. P. 17—21.
18. Arishenskii Yu.M., Kaluzhskii I.I., Uvarov V.V. Nekotorie voprosi teorii plastichnosti ortotropnikh sred [Some problems of plasticity theory of orthotropic medium]. Izv. vuzov. Aviatsionnaya tekhnika. 1969. No. 2. P. 15—18.
19. Lekhnitskii S.G. Teoriya uprugosti anizotropnogo tela [Elasticity theory of anisotropic body]. Moscow: Nauka, 1977.
20. Arishenskii Yu.M. Teoriya listovoi shtampovki anizotropnikh materialov [Theory of sheet forming of anisotropic materials]. Saratov: Izdatel’stvo Saratovskogo universiteta, 1973.
Review
For citations:
Kostyshev V.A., Erisov Ya.A. STUDY OF MECHANICAL ANISOTROPY FORMATION IN ROLLED RING PRODUCTION. Izvestiya. Non-Ferrous Metallurgy. 2016;(1):32-38. (In Russ.) https://doi.org/10.17073/0021-3438-2016-1-32-38
Views:
823
Email this article 