COMPUTATIONAL EXPERIMENTAL EVALUATION OF CONDITIONS FOR COMBINED EXTROLLING PROCESS IMPLEMENTATION USING THE CAPACITY BALANCE METHOD
https://doi.org/10.17073/0021-3438-2016-1-19-25
Abstract
The paper presents the results obtained when solving the problem consisting in determination of the combined extrolling process implementation. The components of a total capacity for the process studied were written in analytical form, their calculation and analysis of the effect of specific factors on implementation of the combined extrolling process was made on PC using a specially developed program. A quantitative evaluation of the process feasibility was made using safety factor as a major criterion for the conditions of aluminum alloy combined extrolling at the pilot combined processing plant.
About the Authors
N. N. Zagirov
Siberian Federal University
Russian Federation
Russian Federation
Cand. Sci. (Eng.), associate prof., Department of metal forming, Institute of nonferrous metals and materials science,
660025, Krasnoyarsk, Krasnoyarsky rabochy, 95
N. N. Dovzhenko
Siberian Federal University
Russian Federation
Russian Federation
Dr. Sci. (Eng.), director of Institute of Petroleum and natural gas engineering of SFU, prof. of the Department of metal forming,
660025, Krasnoyarsk, Krasnoyarsky rabochy, 95
S. B. Sidelnikov
Siberian Federal University
Russian Federation
Russian Federation
Dr. Sci. (Eng.), prof., chief of the Department of metal forming, Institute of nonferrous metals and materials science,
660025, Krasnoyarsk, Krasnoyarsky rabochy, 95
V. M. Bespalov
Siberian Federal University
Russian Federation
Russian Federation
postgraduate of Department of metal forming, Institute of nonferrous metals and materials science,
660025, Krasnoyarsk, Krasnoyarsky rabochy, 95
References
1. Sidelnikov S.B., Dovzhenko N.N., Zagirov N.N. Kombinirovannie i sovmeshchennye metody obrabotki tsvetnyh metallov i splavov [Combined and complex treatment methods of non-ferrous metals and alloys]. Moscow: MAKS Press, 2005.
2. Sidelnikov S.B., Dovzhenko N.N., Galiev R.I. Experimental’nye issledovaniya formoizmeneniya i energosilovyh parametrov protsessa sovmeshchennoi prokatki-pressovaniya prutkov iz aluminievih splavov [Experimental research of forming and energy-power parameters of process combined rolling-extruding rods from aluminium alloys]. Izv. vuzov. Tsvetnaya metallurgiya. 2003. No. 4. P. 49—54.
3. Sidelnikov S.B., Katareva A.A., Dovzhenko N.N. Modelirovanie sovmeshchennogo protsessa nepreryvnogo lit’ya i prokatki-pressovaniya tsvetnyh metallov i splavov [Modeling combined process of continuous casting and rollingextruding of non-ferrous metals and alloys]. Izv. vuzov. Tsvetnaya metallurgiya. 2004. No. 5. P. 34—39.
4. Tselikov A.I., Nikitin G.S., Rokotyan S.E. Teoriya prodol’noi prokatki: Uchebnik dlya vuzov [The theory of longitudinal rolling: Textbook]. Moscow: Metallurgiya, 1980.
5. Kolmogorov V.L. Mehanika obrabotki metallov davleniem: Uchebnik dlya vuzov [Mechanics of metal forming: Textbook]. Ekaterinburg: UGTU—UPI, 2001.
6. Rudskoy A.I., Lunev A.V. Teoriya i tehnologiya prokatnogo proizvodstva: Ucheb. posobie [Theory and technology of rolling production: Textbook]. Sankt-Peterburg: Nauka, 2008.
7. Ageev L.M., Sukharev L.M. Teoreticheskoe sravnenie rashoda energii i koeffitsienta poleznogo deistviya protsessov prokatki-volocheniya i obychnoi prokatki [A theoretical comparison of energy consumption and efficiency for rolling-drawing processes and ordinary rolling]. In: Obrabotka metallov davleniem [Metal forming]: Transact. of high schools of Russian Federation. Iss. 2. Sverdlovsk: Publ. UPI, 1974. P. 45—52.
8. Smirnov V.K., Shilov V.A., Inatovich Yu.V. Kalibrovka prokatnih valkov: Uchebnoe posobie dlya vuzov [Calibration of rolls: Textbook]. 2-nd ed. Moscow: Teplotehnik, 2010.
9. Smirnov V.K., Shilov V.A., Litvinov K.I. Deformatsii i usiliya v kalibrah prostoi formi [Deformations and efforts in calibers of simple form]. Moscow: Metallurgiya, 1982.
10. Perlin I.L., Raytbarg L.Kh. Teoriya pressovaniya metallov [Theory of metal extruding]. Moscow: Metallurgiya, 1975.
11. Grishchenko N.A., Sidelnikov S.B., Gubanov I.Yu., Lopatina E.S., Galiev R.I. Mekhanicheskie svoistva aluminievih splavov [The mechanical properties of aluminium alloys]. Krasnoyarsk: SFU, 2012.
12. Sidelnikov S.B., Belyaev S.V., Dovzhenko I.N., Sokolov R.E., Peshchanskiy A.S., Pletyukhin S.A., Rudnitskiy E.A. Ustroistvo dlya neprerivnoi prokatki i pressovaniya profilei [Device for continuous rolling and extrusion of profiles]: Pat. 2334574 (RF). 2008.
13. Sidelnikov S.B., Bespalov V.M., Dovzhenko N.N., Belyaev S.V., Soldatov S.V., Trifonenkov A.L., Sidelnikov A.S. Ustroistvo dlya neprerivnoi prokatki i pressovaniya izdelii iz tsvetnih metallov i splavov [Device for continuous rolling and extrusion of articles made from non-ferrous metals and alloys]: Pat. 138590 (RF). 2014.
14. Sidelnikov S.B., Bespalov V.M., Dovzhenko N.N., Belyaev S.V., Soldatov S.V., Trifonenkov A.L., Sidelnikov A.S., Fedorova O.V. Ustroistvo dlya neprerivnoi prokatki i pressovaniya katanki iz tsvetnih metallov i splavov [Device for continuous rolling and extrusion wire rod made from non-ferrous metals and alloys]: Pat. 139085 (RF). 2014.
15. Baranov V.N., Voroshilov D.S., Galiev R.I., Dovzhenko I.N., Dovzhenko N.N., Lopatina E.S., Sidelnikov S.B., Soldatov S.V. Ustroistvo dlya neprerivnogo lit’ya, prokatki i pressovaniya [Device for continuous casting, rolling and extrusion]: Pat 2457914 (RF). 2012.
Review
For citations:
Zagirov N.N., Dovzhenko N.N., Sidelnikov S.B., Bespalov V.M. COMPUTATIONAL EXPERIMENTAL EVALUATION OF CONDITIONS FOR COMBINED EXTROLLING PROCESS IMPLEMENTATION USING THE CAPACITY BALANCE METHOD. Izvestiya. Non-Ferrous Metallurgy. 2016;(1):19-25. (In Russ.) https://doi.org/10.17073/0021-3438-2016-1-19-25
Views:
780
Email this article 